WATERPROOFING FOREVER!
PROPERTIES Brushable cementitious waterproofing mortar with excellent adhesion. It fully waterproofs surfaces due to its polymer and water repelling ingredients. D-1 is suitable for positive (preventive exterior application) and negative (interior application for repair purposes) hydrostatic pressure applications. It is resistant to frost and is water vapour permeable (breathable). Classified as product for surface protection of concrete surfaces (c), per EN 1504-2 (principle 2/MC/ moisture control). APPLICATIONS It is applied on surfaces of concrete elements, walls, floors, on surfaces of bricks, cement blocks, in cement mortars, plaster, aircrete, etc. Ideal for the exterior waterproofing of basements and walls, prior to backfilling. Sealed surface with D-1 has to be protected by a drainage membrane (dimpled membrane). D-1 is ideal even for expost waterproofing of vertical or horizontal interior surfaces after removing the plaster with moisture, throughout the area. Excellent for waterproofing underground floors and ground level floors protecting them from rising damp, water tanks, swimming and athletic pools, bathrooms and showers, flower planters, air shafts and tunnels, walls made of brick or concrete blocks before applying the scratch coat of plaster. The product is also recommended for pitched concrete roofs before lining with clay roofing tiles, north facing walls and generally any mineral surface exposed to partial or continuous moisture. USE Surface preparation: Remove all wood wedges, polystyrene and sharp protrusions. Cut the snap ties and tie rods 2-3cm deep and coat them using RUST FREE POWTECHNICAL SPECIFICATIONS (Measurement conditions 20°C and 50% R.H.) • Form - Color: Cementitious mortar - White, gray • Bulk density of dry mortar: 1.10±0.05kg/lt • Bulk density of fresh mortar: 1.60±0.05kg/lt • Maximum grain size: 0.6mm • Water requirement: 6.0lt Brushable waterproofing mortar for walls,
DER (corrosion inhibitor) of DUROSTICK and seal the newly formed holes using D-55, DUROFIX, D-11 SUPER FAST or DS-247 of DUROSTICK. Continue by thoroughly cleaning all surfaces from loose materials, formwork oils and salts using the biodegradable cleaner BIOCLEAN INDUSTRIAL. Rinse thoroughly with plenty of water. Application: D-1 applies to meticulously soaked surfaces in 2-4 equal thickness crosswise coats of 1mm thick each one using an emulsion or a round chalk brush or a roller for emulsion paints or even metal trowels. Empty the product in a clean container with cool water, at a mixing ratio of 25kg powder to 6.0-6.5lt water (1.2-1.3lt for 5kg). It is recommended to mix using a low-rpm drill equipped with the appropriate attachment, until a lump free, homogeneous mass is obtained. The mixture has to be thick enough so it does not drip from an emulsion brush or roller. The mixture remains workable for 60 minutes and each additional coat approximately 2 hours after of the previous one, and while the previous one is still fresh. In case the product remains on the surface longer than 2 hours, resoak the surface. Protect the finish surface for the next 24-48 hours from high temperatures, rain and frost. NOTES • If the substrates to be coated with DUROSTICK D-1 have hairline cracks or there is a need to protect them from natural or other types of vibrations (digging equipment working in adjacent locations), use an acrylic additive. Add the acrylic emulsion D-20 of DUROSTICK in the mixing water at a ratio of one-part water to one-part D-20, up to two parts water to every one-part D-20. Alternatively, use 5 parts water to one-part DUROMAX to ultimately increase the flexibility of the product, the surface resistance to abrasions, its adhesion and waterproofing as well. • D-1 should not be mixed with more water than specified. of water in 25kg mortar • Application temperature: From +5°C up to +35°C • Temperature resistance: From -30°C up to +90°C • Pot life: 1 hour • Application thickness: 1mm/coat • Foot traffic: After 3 hours • Backfilling: After 3 days • Water tightness per DIN 1048* Under water pressure of up to 7 Atm (kg/cm²). floors, basements & roofs
PRODUCT PERFORMANCES: •Strength after 28 days, per ΕΝ 196-1 to: flexion: 7.50±1.00 N/mm², compression: 25.00±1.00 Ν/mm² •Shrinkage per ΑSΤΜ C596: Zero •Permeability sD to CO2 per EN 1062-6: sD = 178m •Water vapour permeability sD per ΕΝ ΙSO 7783-2: sD ≤ 2m (class Ι, water vapour permeable) • Capillary water absorption w per ΕΝ 1062-3: w ≤ 0.06kg/m2.h0.5 • Adhesion to concrete per ΕΝ 1542: ≥1.80 N/mm² • Impact resistance per ΕΝ ΙSO 6272-1: 50Nm (class III) • Reaction to fire after application per EN 13501-1: Euroclass A1 *Laboratory testing by the Ministry of Environment & Buildings 516868/872 ΚΕDΕ 530/58899 www.durostick.com
Brushable waterproofing mortar for walls, floors, basements & roofs Realistic sample application of D-1 sealant (3 crossed coats) with the addition of acrylic emulsion D-20 in a ratio of 1:1 LOAD MINIMUM CONSUMPTION MINIMUM TOTAL THICKNESS Moisture 2.0kg/m2 (2 coats) Approximately 1.5mm Water exerting min. pressure 3.0kg/m2 (3 coats) Approximately 2.0mm Water exerting max. pressure 3.5-4.0kg/m2 (4 coats) Approximately 2.5mm PACKAGING: Bag 5kg, paper bag 25kg CONSUMPTION: 1.0-1.3kg/m²/mm thick coat
ADVANTAGES • Long-term waterproofing on external or internal surfaces. • Excellent adhesion in any mineral, cementitious and plastered surface, without primer. • Excellent protection to surfaces exposed to partial or continuous moisture. • Resistant to frost, to positive and negative hydrostatic pressures. • Breathable. • Easy to use and affordable. www.durostick.com DUROSTICK S.A. ATHENS: ASPROPYRGOS, ATTICA, GR: 193 00, Tel.: +30 211 60 03 500-599, Fax: +30 210 55 99 612 THESSALONIKI: INDUSTRIAL PARK-SINDOS, S.B. 44, STREET DA 10, GR: 570 22, Tel.: +30 2310 795 797, +30 2310 797 365, Fax: +30 2310 797 367, www.durostick.com, e-mail: info@durostick.com 03/2023 Brushable waterproofing mortar for walls, floors, basements & roofs
RkJQdWJsaXNoZXIy MTk0OTg2