| Select:

  • Ελληνικά
  • English
  • Shqip
  • Pусский
header-banner
Info: Your browser does not accept cookies. To put products into your cart and purchase them you need to enable cookies.

DUROSTICK SUPER ACRYLIC

Tile adhesive

DUROSTICK SUPER ACRYLIC

DUROSTICK SUPER ACRYLIC

TECHNICAL SPECIFICATIONS

(Measurement conditions 23°C and 50% R.H.)

Form - Color

Cementitious powder - White

Toxic/Flammable (per ΕΝ 88/379)

No

Bulk density of dry mortar

1.30±0.05kg/lt

Vertical slip per ΕΝ 1308:

<0.5 mm

Water requirement

6.5lt water per 25kg powder

Application temperature

From +5°C to +35°C

Temperature resistance

From -35°C to +90°C

Pot life

5 hours

Open time per ΕΝ 1346

20 minutes

Time for minor adjustments

25 minutes

Grouting

After 4-8 hours on wall; after
24 hours on floor

Foot traffic

After 24 hours

Delivery to use

After 12-14 days

MECHANICAL STRENGTHS

Strength for 28 days, per ΕΝ 196-1, in:

• Flexion

6.20±0.60 N/mm²

• Compression

18.50±1.00 N/mm²

Adhesion strength, per ΕΝ 1348, after:

• 28 days

1.50 N/mm²

• Thermal ageing at +70°C

1.30 N/mm²

• Water immersion for 21 days

1.40 N/mm²

• 25 freeze - thaw cycles

1.35 N/mm²

The experimental measurements were performed per EN 12004, in the Chemical Laboratory of DUROSTICK and were confirmed by the measurements of initial type from MIRTEC (Cert. no: 3354) The following instrumentation was used:
• Flexion-compression: CONTROLS MCCC66 • Detachment: BRAIVE DYNATEST
• NOTE: The product exceeds on average the statutory requirements for C2 adhesive by 35%.

PROPERTIES



Cementitious, high performance white adhesive for ceramic tiles that is fortified with acrylic resins. It offers strong adhesion and presents zero vertical slip. After its final curing, it is resistant to moisture and frost.
Classified C2T per EN 12004.
(MIRTEC/Cert. No.3354).


APPLICATIONS



SUPER ACRYLIC is suitable for low and non absorbent tiles, like klinker, cotto, granite, glass mosaic and porcelain tiles installed on cement screeds and plastered walls, both indoors and out. Recommended for installations on existing mosaic floors or floors that are subject to intense stresses. Adding DUROSTICK ACRYLIC EMULSION in the mixing water, at a ratio of 1:1, further enhances its characteristics so as to meet the requirements of S1 class (deformable adhesive) per EN 12002. The improved (as per its flexibility) adhesive, is suitable for radiant heating and for substrates subjected to intense expansions and contractions.


USE



1. Surface preparation
The application surface have to be sound, clean, free of loose materials, dust, paint, grease and oil. The surface have to be soaked before the application.
It is necessary to prime all absorbent substrates and aircrete, using DUROSTICK ACRYLIC EMULSION or D-20, at a mixing ratio of 1:1 with water.
It is necessary to prime all drywall using the DUROSTICK micromolar stabilizer, AQUAFIX or SOLVENT BASED PRIMER. Lightweight or else, unstable cement screeds, must necessarily be primed with DUROSTICK ACRYLIC EMULSION or D-20 at a ratio of 1part additive to 2 parts water or 1 part DUROMAX to 5 parts water.
Follow all balconies, terraces applications by coating the substrate with HYDROSTOP FLOOR, at 2-3 successive, crosswise layers to ensure the waterproofing of the substrate.


2. Application
Empty the adhesive into a clean container with cool water at a ratio of 2 parts water to 5 parts powder (6.5-7lt water to 25kg powder) and mix with a low speed, electric mixer until a lump free, homogenous mass is created.
Allow the mixture to mature for 5-10 minutes. During use mix periodically, without adding extra water.
Apply the adhesive using a notched trowel, and spread on the substrate.
Then, coat as much surface as is required to work for the next 10-20 minutes (depending on weather conditions), thus avoiding skin formation. Finally, install the tiles in the selected position by tapping softly with a rubber mallet.

CLEANING

Clean all tools with water, immediately after use.

CONSUMPTION



3-5kg/m², depending on the size of the notch of the trowel, the smoothness of the substrate and the dimensions of the tiles.

STORAGE



Store in tightly closed packages, in dry and shaded places for a minimum of 12 months after production date.

SAFETY DIRECTIONS



The product contains Portland cement. Before using, refer to the cautions on the product’s package or the Material Safety Data Sheet.

PACKAGING



Paper bag of 25kg on 1,500kg pallet

ΝΟΤΕ

On outdoor surfaces, it is highly recommended to create expansion joints every 16-20m². Prime the expansion joints with PRIMER-PU, to improve grip, and seal them with the polyurethane sealant, DUROFLEX-PU. Similarly, seal all the joints (5-8mm) at the junction of the tiles and vertical surfaces throughout the perimeter. Alternatively the application of DS-POLYMER, in 32 shades (same with the grout colors of DUROSTICK), ensures sealing without cracking at the junction of the tiles with the skirting and above it as well.