| Select:

  • Ελληνικά
  • English
  • Shqip
  • Pусский
header-banner
Info: Your browser does not accept cookies. To put products into your cart and purchase them you need to enable cookies.

PROFESSIONAL

Resinus tile adhesive

PROFESSIONAL

PROFESSIONAL

TECHNICAL SPECIFICATIONS

(Measurement conditions 23°C and 50% R.H.)

Form - Color

Cementitious powder - White

Toxic/Flammable (per ΕΝ 88/379)

No

Bulk density of dry mortar

1.35±0.05 kg/lt

Water requirement

6.5lt water per 25kg powder

Application temperature

From +5 °C to +35 °C

Temperature resistance

From -35 °C to +90 °C

Pot life

5 hours

Application thickness

Up to 10mm

Open time per ΕΝ 1346

20 minutes

Time for minor adjustments

20 minutes

Grouting

After 3-6 hours on wall; after 24 hours on floor

Foot traffic

After 24 hours

Delivery to use

After 10-14 days

 

MECHANICAL STRENGTHS

Strength after 28 days, perΕΝ 196-1, in:

• Flexion

5.05±0.70 N/mm²

• Compression

17.10±1.00 N/mm²

Adhesion strength, per ΕΝ 1348, after:

• 28 days

1.30 N/mm²

Thermal ageing at +70°C

1.15 N/mm²

Water immersion for 21 days

1.20 N/mm²

25 freeze - thaw cycles

1.20 N/mm²

The experimental measurements were performed per EN 12004, in the Chemical Laboratory of DUROSTICK and wereconfirmed by the measurements of initial type from MIRTEC (Cert. no: 3353) The following instrumentation was used:
• Flexion-compression: CONTROLS MCCC66 • Detachment: BRAIVE DYNATEST
• NOTE: The product exceeds on average the statutory requirements for C2 adhesive by 20%.

PROPERTIES


Cementitious, high performance white adhesive for ceramic tiles, fortified with acrylic resins, and minimal vertical slip. Distinguished for its high initial and final bonding strengths, as it offers strong adhesion. After its final curing, it is resistant to moisture and frost. Classified C2 per EN 12004. (MIRTEC/Cert. No. 3353).


APPLICATIONS


PROFESSIONAL is suitable for small and large size tile installations on floor cement screeds and plastered walls, both indoors and out. Adding DUROSTICK ACRYLIC EMULSION in the mixing water, at a ratio of 1:1, further enhances its characteristics so as to meet the requirements of S1 class (deformable adhesive) per EN 12002. The improved (as per its flexibility) adhesive,  is suitable for non absorbent substrates, subjected to intense expansions and contractions, as well as for outdoor spaces that are exposed to adverse weather conditions. The adhesive is suitable for every type and size tile.


USE

1. Surface preparation


The application surface have to be sound, clean, free of loose materials, dust, paint, grease and oil.  The surface have to be soaked before the application. It is necessary to prime all absorbent substrates and aircrete, using DUROSTICK ACRYLIC EMULSION or D-20, at a mixing ratio of 1:1 with water.
It is necessary to prime all drywall using the DUROSTICK micromolar stabilizer, AQUAFIX or SOLVENT BASED PRIMER. Lightweight or else, unstable cement screeds, must necessarily be primed with DUROSTICK ACRYLIC EMULSION or D-20 at a ratio of 1part additive to 2 parts water or 1 part DUROMAX to 5 parts water.
Follow all balconies, terraces applications by coating the substrate with HYDROSTOP FLOOR, at 2-3 successive, crosswise layers to ensure the waterproofing of the substrate.

Application:

Empty the adhesive into a clean container with cool water at a ratio of 2 parts water to 5 parts powder (6.5-7lt water to 25kg powder) and mix with a low speed, electric mixer until a lump free, homogenous mass is created.
Allow the mixture to mature for 5-10 minutes. During use mix periodically, without adding extra water.
Apply the adhesive using a notched trowel, and spread on the substrate.
Then, coat as much surface as is required to work for the next 10-20 minutes (depending on weather conditions), thus avoiding skin formation. Finally, install the tiles in the selected position by tapping softly with a rubber mallet.

NOTE

On outdoor surfaces, it is highly recommended to create expansion joints every 16-20m². Prime the expansion joints with PRIMER-PU, to improve grip, and seal them with the polyurethane sealant, DUROFLEX-PU. Similarly, seal all the joints (5-8mm) at the junction of the tiles and vertical surfaces throughout the perimeter. Alternatively the application of DS-POLYMER, in 32 shades (same with the grout colors of DUROSTICK), ensures sealing without cracking at the junction of the tiles with the skirting and above it as well.

CONSUMPTION

3-5kg/m², depending on the size of the notch of the trowel, the smoothness of the substrate and the dimensions of the tiles.

CLEANING


Clean all tools with water, immediately after use.

 

STORAGE

Store in tightly closed packages, in dry and shaded places for a minimum of 12 months after production date.

SAFETY DIRECTIONS


The product contains Portland cement. Before using, refer to the cautions on the product’s package or the Material Safety Data Sheet.

PACKAGING


Paper bag of 25kg on 1,500kg pallet.